From Wikipedia, the free encyclopedia
Linux is a family of open source Unix-like operating systems based on the Linux kernel, an operating system kernel first released on September 17, 1991 by Linus Torvalds. Linux is typically packaged in a Linux distribution (or distro for short).
Distributions include the Linux kernel and supporting system software and libraries, many of which are provided by the GNU Project. Many Linux distributions use the word "Linux" in their name, but the Free Software Foundation uses the name GNU/Linux to emphasize the importance of GNU software, causing some controversy.
Community icon by Alpár-Etele Méder, licensed under CC BY 3.0
sudo traceroute 1.1.1.1
can show you how far your connection request gets (whether it's blocked by your pc, your router, or somewhere on the internet).
You may have to install it first.
sudo find /etc -name *wg*
find ~ -name *wg*
can help find left-over config files.
All I got was wget, so this is clean
Give the output of route, maybe there is a left over route.
@CameronDev @anytimesoon This is why I suggested netstat -nr
Yup, didn't read your comment properly, but that will also work.
The output was pretty much the same from this as from netstat -nr
I would share it here, but I can't access the internet from that machine
@anytimesoon @CameronDev It should be as both commands do more or less the same thing, the question is your default route correct and are there any other routes that might be misdirecting your data.
I'm not entirely sure which of the list is the default route is, but absolutely see my WiFi router on the list. Took a picture as recommended by @CameronDev
@anytimesoon Assuming 192.168.1.1 is your wifi router, it looks correct. Can you ping that IP?
~~Nope. Destination host is unreachable when pinging~~
I changed to a different router and can at least ping that now, but still no internet
~~Take a photo of the output? First few lines are most important, but ideally all would be good.~~
Edit: actually, dont want to crowd the kitchen, good luck!
This is what mine looks like for contrast:
0.0.0.0 50.251.249.54 0.0.0.0 UG 0 0 0 bridge0
50.251.249.48 0.0.0.0 255.255.255.248 U 0 0 0 bridge0
192.168.122.0 0.0.0.0 255.255.255.0 U 0 0 0 virbr0
In my case, 50.251.249.54 is my gateway and .48 my broadcast. I am static routed so no NAT.
Sorry formatting is whack, Friendica does not understand tabs.
So that looks similar to what I have. Wonder why it's not working
I would look at your interface configuration and your routing, ip addr show, netstat -nr and go from there. Also might check iptables, iptables -L -n and make sure there aren't any iptable rules blocking your access.
IP tables have no rules, but netstat is showing traces of WG. Two of the interface names are the same as WG config name I used
Did you try to ping the router IP, 192.168.1.1 and see if it responded?
~~I did, but no response~~
I changed to a different router and can at least ping that now, but still no internet
@anytimesoon With that different router, now try a traceroute 1.1.1.1, if you get a response from the first hop, 192.168.1.1, then something is wrong with the NAT on the router or your cable service or fiber or whatever it is, is not working.
Unlikely to be something wrong with that, tbh. Everything else on that network has internet access. The issue is limited to the laptop
@anytimesoon I'm a bit at a loss then. I do have a Comcast router that is weird in that ARP only works at boot time so if I plug a new device into it, it won't route for that device unless I reboot it.
No worries. Thanks for your help! I'll post here if/when I find a solution
Hi
Did you remove wireguard the meta package or everything wireguard installed? I don't know Pop but other distros install additional tools and configs like wireguard-dkms.
Also, if possible, after completely purging every wg you could try booting into a previous kernel on your system to see if that changes anything.